Selection Guide

Hone-O-Drive™ Overdrive Unit Selection

Determine Bolt Pattern for Proper Model Selection

These units mount directly to the Ford type 9″ differential housing, replacing the pinion gear bearing housing and using the existing pinion gear, bearings, crush washer, lock-nut, washer, and U-joint yoke.

To determine which models fit your Ford type 9″ differential housing measure the center-center distance between the lower two bolts on your differential housing as shown in Figure 1 below. If this center-center distance is 3-9/16″ then Models B200 and B210 are the ones that fit. If this center-center distance is 3-3/4″ then Models B220 and B230 are the ones that fit.

Hone-O-Drive™ Model Selection Guide

Figure 1

Determine Lubrication Option

The Models B200 and B230 share oil and lubrication with the Ford type 9″ rear differential. These models are designed to gravity flow the oil from the rear differential into the Hone-O-Drive™ unit for lubrication. These models are for installations where the rear pinion is at or near horizontal to the road surface such as with most muscle cars. Additional oil will need to be added to the rear differential to accommodate the oil needed to lubricate the Hone-O-Drive™ unit once installed to the Ford type 9″ differential housing and oil levels must be checked and oil changes made according to maintenance specifications.

The Models B210 and B220 are designed with an independent oil system and do not share oil or lubrication with the Ford type 9″ rear differential. These models are for installations where the rear pinion is at a substantial angle to the horizontal such as with off-road or lifted vehicles. Oil is added to the Hone-O-Drive™ unit independently from the rear differential and oil levels must be checked and oil changes made according to maintenance specifications separately from the rear differential.

ORDER YOURS TODAY!



Manual Shifter Selection

We offer several manual shifter configurations to compliment the Hone-O-Drive™ overdrive. Our manual shifters are designed to authentically replicate the look and function of the original manual shifters offered in the 1960′s and 1970′s.

Model S110 Manual Shifter

Model S110 Manual Shifter

Model S110

The model S110 manual shifter is designed to authentically replicate the look and function of the original manual shifters that were first used in the Shelby American Mustangs and the early Motion Performance Corvettes and Camaros. If you are restoring one of these vehicles then the model S110 manual shifter would be the most authentic choice. This model is designed to mount on either the driver side or passenger side of the transmission tunnel.



Model S120 Manual Shifter

Model S120 Manual Shifter

Model S120

The model S120 manual shifter is designed to authentically replicate the look and function of the original manual shifters that were typically installed on vehicles in the late 1970’s and later. This model is designed to mount on either the driver side or passenger side of the transmission tunnel.



Model S130 Manual Shifter

Model S130 Manual Shifter

Model S130

The model S130 manual shifter is designed to authentically replicate the look and function of the original manual shifters that were typically installed on vehicles in the mid 1970’s. This model is designed to mount on either the driver side or passenger side of the transmission tunnel.



Model S140 Manual Shifter

Model S140 Manual Shifter

Model S140

The model S140 manual shifter is designed to authentically replicate the look and function of the original manual shifters that were typically installed in pick-up trucks and off-road vehicles such as the Ford Bronco. This model is designed to be mounted on the flat top of the transmission tunnel in these vehicles.

ORDER YOURS TODAY!



Electronic Shift Actuator Selection

Model S210 Electronic Shift Actuator

Model S210 Electronic Shift Actuator

Model S210

The model S210 electronic shift actuator is offered to allow remote electronic shifting at the push of a button or the flick of a switch. The model S210 operates in a push-pull type configuration by reversing the polarity of the 12 VDC power applied through a momentary type switch available through after market vendors. The model S210 can be conveniently mounted utilizing your custom mounting hardware and either ridged or flexible shifter linkage also available through after market vendors.

ORDER YOURS TODAY!


Strict Standards: Only variables should be assigned by reference in /home/content/00/5118900/html/hone-o-drive/wp-content/themes/mystile/comments.php on line 28